Home About Us Products Applications Quality News Testimonials Enquiry Contact Us
  PTC Thermistors
  Thermistor Protection Relay
  Resistance Temperature Detector (RTD)
  Single and Dual Element Stator Winding RTDs
  Thermal Overload Protector (TOP)
  Electric Motor Anti-Condensation Heater
  Thermowells
     
  Electric Motor Anti-Condensation Heater


 
 
Thermo System Anti-Condensation Heaters provides low cost protection against  condensation within  rotating electrical equipment. The electric motor anti-condensation heater is specially designed for moisture proofing. Typical applications would  be electric motors, generators and alternators  which operate in damp or wet conditions. Examples would include off shore, shipboard and marine equipment, dockside  cranes, well pumps and all equipment operating in a  tropical environment. Specifying anti-condensation heaters  at the design stage can save the expense of costly rewinds and down time.
 
     
  Key Specifications/Special Features:  
 
High-voltage Insulation Voltage more than 2.5KV AC
High Temperature Resistance of Insulation Material more than 250C
Low cost and Easy to fit.
Designed specifically for Electric Motors arid Generators.
Helps to prevent winding failures and breakdowns, which can lead to plant shut down and associated costs.
 
     
  Specifications:  
 

Type No

Dimensions (mm)

Lead Length (mm)

Watts

A.C. Voltage

Recommended Frame Size

TS23071

220x13x2

160

10

230V50Hz

71

TS23090

 260 x 13 x 2

340

20

230V50Hz

80/90

TS230112

350 x 13 x 2

440

30

230V50Hz

100/112

TS23060

460 x 13 x 2

740

40

230V50Hz

132/60

TS230200

630 x 13 x 2

850

50

230V50Hz

180/200

TS230280

800 x 13 x 2

900

60

230V50Hz

225/280

TS230355

950 x 13 x 2

1000

80

230V50Hz

315/355

 
     
 
 
     
     
  A. High quality dip soldered joint.  
  B. 80 /20 Ni Cr Heating Element. Covered with Fiber Glass Sleeve.  
  C. Polyester backed adhesive tape insulation  
  D. Glass Fibre Braid Insulation.  
  E. Acrylic adhesive backed galss fibre tape insulation and Lead reinforcement.  
  F. Heat proof lead wire  
     
  1. INSTALLATION  
 
Please confirm the type of the heater must conform to the electric motor’s matching requirement.
Clean up the electric motor stator and the winding coil.
Lie the heater out, the lead wires should be leaned in the side of the stator ferrite core.
If the Electrical motor uses one piece anti-condensation heater, please install the heater in the electric motor’s driving end.
 
If Electrical motor uses two pieces of anti-condensation heater, one heater should be installed in the driving winding end, the other heater should be installed in the non-driving winding end.
 
Wrap the heater around the outside of the starter end winding coil on the connection end and tie in the place preferably with wide polyester ties. Narrow ties or strings can cause damage to the heater elements, if they are tied tightly
 
Do not overlap the heater directly on the top of itself as this cause a hot spot which lead to reduce thermal life of the insulation expose to the spot temperature.
 
 
     
  3. BREAKDOWN AND MEASURE  
 

Failure

Cause

Corrective Method

Heater  doesn't work

1. The power source was unconnected.                                    2. The contact of the lead wire and the wiring terminal is not good. 
3. Heater's interior was damaged.

1. Connect the power source.
2. Firm the contact of lead wires and wiring terminal.  
3 Replace the heater

Sometimes work, Sometimes dose not work

The contact of the lead wire and the wiring terminal is not good.

Firm the contact of lead wires and wiring terminal.

 
     
 
 
     
 
The Anti-condensation Heaters/Space Heaters find application in electric motors & alternators to prevent formation of condensate in the windings of these electric motors & alternators and thus prevent them from burning.
 
     
     
     
 
Being a quality conscious company, we place quality as the nucleus of all our endeavors. Our quality inspectors carefully monitor the entire production process at every level of operation to check that our products conform to relevant quality.
 
 
 
Special attention is given on the procurement of the raw material. We conduct periodic inspections and conduct various tests to make our products flawless. Each and every piece is tested to ensure that it performs efficiently after the consignmen
 
     
  More >>  
  Click here to download our Catalogue
 
 
 
Home        |        Trade Enquiry        |        Applications        |        Quality        |        Testimonials        |        Contact Us
 
Copyright @ Thermo System 2011.   |   Designed & Developed by : Perfect View Media